How to Fix Common Plumbing Problems

There are common plumbing problems that will spring up in your home anytime. Some of these problems are quite easy to fix if you have a few essential tools. It’s important to have these tools at home to help you fix minor plumbing emergencies. Many times, you’ll experience a clogged toilet, slow draining sink or low water pressure.

If you’re the handy type of person, you can tackle small repairs in your house such as unclogging your toilet or changing a worn-out washer. However, bigger and complicated plumbing repair work should be done by professional plumbers. Remember, even a thorough plumbing inspections cannot prevent occasional leak or clog, especially in older homes. Most of these common plumbing issues equally require common solutions.

Here are some of the common plumbing problem

1. Low water pressure

When you experience low water pressure, the problem could be the sink faucet. Start by checking whether this problem is affecting both the cold and hot water. If the low water pressure persists in both hot and cold water, then the main cause could be the aerator.

The culprit is the calcium deposits that slowly build up inside the faucet aerator. A blocked aerator is an easy thing to fix by cleaning out the debris that builds on it. In case you notice the low water pressure soon after cleaning the aerator and shower head, the problem might be more complex. Call a qualified plumber to fix this problem for you.

2. Slow or clogged drains

Whether its stopped-up toilet, sink or tub draining slowly, every homeowner will experience these plumbing problems. More often these plumbing issues are caused by a collection of debris over the time. The problem could be a partial or complete clog. Shine a flashlight inside the drain to check if you can spot any problem.

You can use a plunger to fix the problem. This is a very important tool to have in your home. A plunger is designed to use air pressure to dislodge any debris causing a clog. If you’re dealing this problem more frequently, then it’s time to seek help from a professional plumber.

3. Running Toilet

Are you tired of jiggling your toilet handle after flashing? Well, maybe it’s time to replace some of its inner workings. A toilet will run when a defective flapper valve allows the water to pass from its tank to the bowl.

Other causes might be an imbalanced float or loose fill tube. With a toilet repair kit, you’ll require a little effort to fix the problem. Occasionally, a toilet can run due to other complex reasons. In case you have replaced the float apparatus, flapper, and fill tube, and the problem persists then do not hesitate to call for help.

4. Slow draining tub

A tub drain can easily be clogged by human hair, which slows the water from moving down the tub drain. You can either use the needle nose pliers or Zip-it tool to reach in and clear out all the debris. If your tub has a tub stopper, then you should remove it to access the hair clog. It’s a good practice to remove any debris from your tub drain more regularly. Leaving it for long, this debris can clog your tub drain completely

Can I Install an HVAC System By Myself?

Your reliable HVAC will eventually have to be replaced, as it will die out altogether or become too inefficient. Installing an HVAC is something that should only be attempted by a licensed HVAC professional. This is not a job for even the most ambitious do-it-yourselfer. This installation requires considerable knowledge of electrical work, sheet metal work, and some plumbing work. Installing a new furnace is a somewhat complicated process, and only licensed Dallas Plumbing Company professionals.

If you are switching from an electric furnace to a gas furnace (or vice versa), the project is even more complicated. Dallas Plumbing Company technicians undergo rigorous training after completing their Associates Degree and are trained to handle any contingency that comes up during the installation process.

The Installation Process

All gas and electrical must be turned completely off before any work is started. Leaving power or gas to the furnace unit on while uninstalling it is extremely dangerous and is not recommended under any circumstances. Once the utilities are turned off, it is safe to remove the old furnace. All gas supplies and wires need to be disconnected, and ductwork and vent pipes should be detached and removed. The Dallas Plumbing Company professional who removes your HVAC will be wearing gloves and protective gear to avoid any injuries.

If your existing furnace is connected to your AC unit, the connection will also have to be disassembled. Once the unit has been completely dismantled, and all the screws have been taken out of the base, the old furnace can be hauled out and recycled or discarded properly.

Preparing the Area for the New Furnace

The next step for the technician will be to thoroughly clean the area where the new furnace will be installed. If there is any dust in the area, it must be vacuumed up. You don’t want to spend all that money on a new furnace just to let it be contaminated with dust when you have it installed.

Once the area is entirely free of dust and debris, it is time for the technician to start installing your new unit. The pipes, wires, and ductwork will be connected to the new furnace. After that, the technician will connect the thermostat and turn the gas and power supplies back on. Now the technician can test the system and check the ductwork for leaks.

If you’re having a gas furnace installed it must also have all the gas supply lines inspected for leaks. All connections, even those to the AC unit must be checked. The system itself must also be carefully examined for carbon monoxide leaks and other gas emissions, which again, is something that must be done by an HVAC professional, as it requires specialized knowledge and equipment.

Leave it to the Professionals

As a homeowner, you should choose what type of furnace will best suit your needs. Once you select your unit, the rest should be left up to the pros. Removing your old HVAC and installing the new one is a big, dangerous job, and there are a countless number of ways it can result in serious injuries or expensive repairs.