What is an HVAC System and
Why Should You Consider Replacing It?

HVAC stands for Heating Ventilation and Air Conditioning and includes the complete system that cleans the air and gives cool or warm air depending on your needs. HVAC is the term most commonly used by industry professionals. Most consumers refer to the system as “air conditioning” for cooling and “heating” or “furnace” for the warmth in cold weather. However, the air conditioning and heating functions are usually all in one HVAC system. These systems found in most homes in Texas are split systems. The split system includes an outdoor condensing unit which dispels heat and sends the cooling back to an indoor unit containing an evaporator coil for cooling and a fan for circulation.
HVAC systems should be installed by experts and are best chosen for their energy saving, air quality and performance features. If your HVAC system is older than few years then it may be time to check into upgrading your older HVAC system with a high efficiency system. Here are some advantages to upgrading your HVAC system that you might want to consider.

  • Replacing an old furnace with a high-efficient one can start saving you cash on your very first bill. Heaters are estimated by AFUE (yearly fuel use productivity.) Many older systems work around 65 percent AFUE, which means 35 percent is essentially lost. High-efficiency units work at 93 to 98 percent AFUE, which means less heat is being wasted each time it’s used. That implies it’s better for the earth and your wallet too.
  • The latest technology HVAC system delivers much more than heating or cooling. It helps in maintaining a steady temperature in each room in your home, improves air quality and offers better humidity control. The result is greater comfort and energy savings.
  • High efficiency systems have variable speed condensers and fan motors that guarantee better circulation and more even temperature all through your home. Variable speed fan motors precisely adjust the air output or capacity according to your home’s temperature settings and offer energy savings over older single speed fans.
  • Variable speed motors may run longer, but provide better circulation and afford better comfort in each room. By reducing the heavier loads on your electricity caused by more frequent on/off changes, they can save in energy cost.
  • Older models tend to be a little noisier when they cycle on and off. The new system has better sound control that means your system is felt but not heard.
  • If you are considering selling your home in couple of years, a new high efficiency HVAC system can be an advantage. Home buyers look for advantages, and this can be a major checkpoint on their list. By upgrading now, you can enjoy the increased comfort and energy savings now and have an added selling feature later.

So is it the time to change your HVAC system? To enable you to settle on the best choice, we’re glad to assess the system you have, and demonstrate to you the best alternatives for your home. Contact us today.

3 DIY Solutions For Your Garbage Disposal Repair

When your garbage disposal system is working smoothly, cleaning up after meals is easy. However when things go wrong, it can put a serious damper on your post dinner kitchen clean-up routine. Professional plumbing assistance is readily available, but here are some quick DIY solutions that you can try yourself before calling for professional plumbing help.

  • Clearing The Clog: The main reason that a garbage disposal can’t grind anymore is something might be stuck inside it. Try to remove any blockage that might be causing hindrance. This work if there is any clogging. For safety reasons, don’t ever try to stick your hand down into the disposer. Instead, look underneath your sink, unplug it, then try to reach inside the disposer to remove the clog from sink side. If the problem continues, you may need professional help.
  • Odor Removal: Over time, garbage disposals can emit a foul smell. Try to get rid of the nasty odor by pouring a liquid soap solution down the drain along with some cold water and let the disposal run for a couple of minutes in order to eliminate the cause of the smell due to accumulation of bacteria and other micro-organisms. You can also try odor repellent products or a drain cleaning product.
  • Leakage Repair: If your garbage disposal system seems to be leaking, then make sure that all the nuts, bolts and connections are properly secured. Always unplug the unit from under the sink to prevent possible shock. If it’s a minor leakage, you can use plumber putty or caulk to seal those areas. However if there is any leakage, a broken hose, or any other part, you may need to buy the spare part in order to stop the leakage.

Hiring professional plumbing experts to handle your garbage disposal problems may be your best option, because they are trained and experienced to handle various tricky jobs such as replacing a disposer or fixing leaks, etc that you can’t do.Dallas Plumbing Company is a a trusted and reliable name for plumbing and air conditioning solutions since 1903. All our technicians are trained, experienced, drug-tested and background-checked. To hire a plumbing expert, give us a call at 214-340-6300 or contact us.

5 Must Have Plumbing Tools Every Homeowner Should Possess

Every household has to deal with some sort of plumbing problems. Imagine a situation where you find yourself standing knee deep in flooding sewage water, how would you handle the situation? Being prepared is the key difference between calmly handling a situation instead of being panicked by it. It can prevent your few hours of stress and lasting, expensive damages. When it comes to your household plumbing, there are numerous ways through which you can keep yourself prepared for an emergency. There are many plumbing tools used by any professional plumber but here we’ve listed the five must have plumbing tools that every homeowner should have:

  • A set of Plungers: There are various types of plungers available in market. However for homeowners, two types of plungers are recommended: a cup plunger and a flange plunger. The cup plunger is suitable for cleaning drain clogs in sink, tub or any other surface where the drain rests on a flat surface. However flange plunger is primarily used for cleaning of toilets as it come with an additional soft rubber coming from the cup. This additional feature allows flange plunger to make a seal on curved surfaces i.e. toilet bowl.
  • Pipe Wrench: It is a tool having a heavy metal handle with two wide jaws like protrudences to adjust and fit any plumbing connection. Pipe wrenches are designed and built in such a way to loosen, tighten removal or replace a water pipe efficiently.
  • Duct Tape: A duct tape is a quick solution for any general plumbing emergency. Its prime role is to create a seal in and around a leak so as to block off any water trying to make it way out. It is water resistant in nature which makes it a perfect stop gap solution amidst finding a leakage and a permanent fix.
  • An Auger & a Snake: These two tools tend to work in tandem. These tools are primarily used for drain clog that are hard for an average plunger to handle. Auger is generally used for toilet as they are designed to easily move through a toilet drain and hook onto potential clog to pull it out. However snake is a more versatile tool as it can be used for various other surfaces such as tubs, sinks, showers etc.
  • An adjustable Wrench: It is a multi functional and multi-purpose tool that is used for tightening and loosening of nuts and bolts of all types.

However if your plumbing still persists, you’ll have to seek professional help. Dallas Plumbing Company is a trusted local name for all sort of plumbing and air-conditioning solutions across Dallas. Give us a call to get professional plumbing services at your door step.

What is HVAC System

HVAC is a common term for many homeowners. The term HVAC stands for heating, ventilation, and air conditioning. Are you aware of the components that make up an HVAC system? This article is aimed at explaining about various components and their functionalities.

  • The Furnace: The furnace is a vital component that takes up a majority of the space in HVAC system. It is usually located in the basement. The furnace moves air from the heat exchanger into the air duct.
  • Heat Exchanger: It is not a part of furnace but it is located inside the furnace. Heat exchanger has its own set of capabilities. The prime function of the heat exchanger is to add heat to the air coming from the combustion chamber.
  • Evaporator coil: This HVAC part is also in the furnace but its job is entirely different. Refrigerant is a fluid that causes cooling flows through the evaporator coil. Whenever the hot air passes through it, the coil absorbs the heat from it. This mechanism is responsible for inflow of cold air through the air duct across your home.
  • Condensing Unit: Its function is similar to that of evaporator coil but the difference is that the condensing unit is just meant for an outdoor HVAC unit. It is a cube shaped unit that exchange the heat with the air that passes over it. However the condensing unit in return gives off heat.
  • Thermostat: This is the most common part of the HVAC system that you’re most familiar with. It is a small appliance placed on the wall of main level of your home. Depending on your choice of temperature, you can either turn on the air conditioning or heating system.
  • Refrigerant Tubes: These tubes are made up of metal and connect the evaporator coil with condensing coil. In short, it works as a connector for indoor and outdoor HVAC units. Cooling refrigerant is stored under these tubes under a wide range of temperatures.
  • Vents: Vents allows the passage of air through air ducts to room.
  • Ductwork: Air ducts allow movement of air throughout your home. Air enters into HVAC system through certain sections of the ductwork.
  • Heating pump: when it is warm outside, the heat pump takes heat from inside to outside. However during the cold season, it does opposite. All these components of the HVAC work in sync to function properly and efficiently.

This is the first part of the series of blog on HVAC system. Keep visiting us for more information on HVAC system and other plumbing solutions. Dallas plumbing Company is a trusted name for plumbing and air conditioning solutions across Dallas.

What a Video Inspection of a Plumbing Line Should Include

A video inspection can be useful when you need help with getting a plumbing line in your home analyzed and cleaned out properly. A video inspection will work to review what is keeping a line from staying healthy but it must especially include several points to keep the inspection process working well.

A Proper Electronic Location

A video inspection should include a full electronic analysis of the specific spot where something troubling may be found in your plumbing system. The inspection can include a review of something like a clog or a dislodged section of a pipe. But whatever the problem might be, your video inspection should include a full analysis where the issue might be.

An electronic review could include information on how deep the issue is and how many feet or inches it is within a pipe. This may be used for sensors or a measurement of whatever is being inserted into the plumbing line. Whatever it may be, it is critical to see how deep the issue might be so it becomes easier for the problem to be fixed as soon as possible.

High Resolution Is Important

The type of clog or issue impacting your plumbing line must be fixed as soon as possible. The problem with so many clogs is that they all require different cleaning compounds. A high-resolution readout must be used in the video inspection to get a clear idea of what is inside a system. This ensures that it will be easy for a problem to be fixed up and treated right.

What About Items Moving Through?

Sometimes a plumbing video inspection can include a review of how items might move through your plumbing system. A video review can help you with identifying problems relating to the way how the plumbing system is treated.

The analysis that comes with a video inspection can help you to identify anything that moves through and if there is a certain space that might have to be treated in particular. Sometimes a clog or other issue might be on the bottom part of a pipe while in other cases it could be at the top. This helps with getting a clear idea of how a treatment should be utilized and what can be handled to keep additional problems from being a serious threat to your plumbing system.

Your video inspection for your plumbing line should be handled carefully and clearly to ensure that there any problems that may be found are resolved well. A great inspection process will ensure that any problems within your system are fixed properly and with care. Be sure to contact a plumber for helping with getting your system analyzed with a full video review so you can get a clear idea of what the issue in a system might be.

How to Fix Common Plumbing Problems

There are common plumbing problems that will spring up in your home anytime. Some of these problems are quite easy to fix if you have a few essential tools. It’s important to have these tools at home to help you fix minor plumbing emergencies. Many times, you’ll experience a clogged toilet, slow draining sink or low water pressure.

If you’re the handy type of person, you can tackle small repairs in your house such as unclogging your toilet or changing a worn-out washer. However, bigger and complicated plumbing repair work should be done by professional plumbers. Remember, even a thorough plumbing inspections cannot prevent occasional leak or clog, especially in older homes. Most of these common plumbing issues equally require common solutions.

Here are some of the common plumbing problem

1. Low water pressure

When you experience low water pressure, the problem could be the sink faucet. Start by checking whether this problem is affecting both the cold and hot water. If the low water pressure persists in both hot and cold water, then the main cause could be the aerator.

The culprit is the calcium deposits that slowly build up inside the faucet aerator. A blocked aerator is an easy thing to fix by cleaning out the debris that builds on it. In case you notice the low water pressure soon after cleaning the aerator and shower head, the problem might be more complex. Call a qualified plumber to fix this problem for you.

2. Slow or clogged drains

Whether its stopped-up toilet, sink or tub draining slowly, every homeowner will experience these plumbing problems. More often these plumbing issues are caused by a collection of debris over the time. The problem could be a partial or complete clog. Shine a flashlight inside the drain to check if you can spot any problem.

You can use a plunger to fix the problem. This is a very important tool to have in your home. A plunger is designed to use air pressure to dislodge any debris causing a clog. If you’re dealing this problem more frequently, then it’s time to seek help from a professional plumber.

3. Running Toilet

Are you tired of jiggling your toilet handle after flashing? Well, maybe it’s time to replace some of its inner workings. A toilet will run when a defective flapper valve allows the water to pass from its tank to the bowl.

Other causes might be an imbalanced float or loose fill tube. With a toilet repair kit, you’ll require a little effort to fix the problem. Occasionally, a toilet can run due to other complex reasons. In case you have replaced the float apparatus, flapper, and fill tube, and the problem persists then do not hesitate to call for help.

4. Slow draining tub

A tub drain can easily be clogged by human hair, which slows the water from moving down the tub drain. You can either use the needle nose pliers or Zip-it tool to reach in and clear out all the debris. If your tub has a tub stopper, then you should remove it to access the hair clog. It’s a good practice to remove any debris from your tub drain more regularly. Leaving it for long, this debris can clog your tub drain completely

Water Supply Lines and Residential Plumbing

Water Supply Lines

Water supply lines are located throughout any home plumbing system; in fact, you probably already noticed that under the sink or toilet tank a small pipe connected between the faucets or tank and the water shut-off valve.

It is important that one knows as much as possible about water supply lines because it is one of the easiest plumbing repairs around the house.

Even though supply lines leakages are considered an easy fix problem, the reality is that most people fail to properly diagnose water leakage in their home.

Most leak problems involving supply lines are small and steady leaks, which mean that goes unnoticed for months or even years and when someone notices the problem; there will be mold and bad smell present in the areas around the supply lines.

My goal in this page is to educate and promote awareness about water supply lines, how to diagnose a leak and how to fix it yourself.

Determining if the leak is in the supplies?

  1. The most common sign of leakage is the presence of mold under the water supply lines and around the areas where water is leaking from.
  2. Check the supplies for water rust and hardness buildup between the fittings and the supplies.
  3. If mold or hardness is present, you will probably notice water running or dripping even if it is slowly along the supplies, this means that the supplies need to be replaced. P.s: Carefully check the source of the leak before replacing anything. Water leaks are very misleading and, you don’t want to waste time and money fixing the wrong fixture.  The best way to check for leakage is to have a flashlight and a mirror handy; this will allow you to diagnose the area with more precision and clarity.

Before replacing a supply line:

Before replacing the supplies, one must understand that are different types of supply lines available in the market.

Water supply lines for faucets and toilets are available on a variety of materials but, the following are the most common materials: plastic, chrome and metal.

Before buying the water lines, determine if the supplies will be used for faucets, tub, or toilet, also, learn about the length and the size needed.

Why do you need to know that?

Water supply lines for toilets are different from the supply lines used for faucets. The supplies will differ in length, diameter and head size.

Toilet Supply Line:

The toilet supply lines are shorter than the faucet supplies. A toilet supply is shorter and has a bigger head in the end to proper fit in the fluid master bottom pipe connection, which is bigger in diameter than the faucet piper connection.

Faucet Supplies:

The faucet supplies are in most cases twice as longer as the toilet supply. In most cases, the plastic and chrome supplies will have the same diameter; however, the head of the faucet supplies will be smaller than the toilet one.

Tools needed to replace supplies:

You don’t need to use leather gloves, however, latex gloves are advised to have with you, also, you will need a razor blade, different sizes of channel locks, and 7/16 crescent wrench, thread sealing tape, supply lines, new ring gaskets.

Replacing supplies:

This is probably one of the easiest of all plumbing jobs that you will ever do in your home, as long as you follow the below instructions.

  1. Shut off the water at the angle stop valve (s), if there isn’t an angle stop valve by the fixture, then you might have to shut the water off for the whole house at the main valve inside or outside the house in the meter.
  2. Drain all the water from the local pipe, as much as possible by flushing the toilet, running the tube, running the sink etc.
  3. With the proper tool, lose the nuts and unscrew the supply (supplies) on both ends, remove the supply (supplies), make sure to have a small container and rags to dry out the rest of the water.
  4. If you bought plastic supplies, take the proper measurement from the old supply (supplies) and with the razor blade cut the new supply (supplies) on the needed length.
  5. Wrap the threads in the angle stop valve three or four times and, after the nuts and gasket rings being through the supply (supplies), insert the supply inside the valve fitting and then, manually tight it on both sides, because to not cross thread the nuts, you don’t want to damage them, once you have threaded all the way, use the crescent wrench to finish tightening the nuts.
  6. Turn the water back on and check for leaks, if there are no leaks, you have accomplished the task successfully. This whole process should take about 15 to 30 minutes.

Check the Weatherstripping to Decrease Heating Costs

When you have a proper weather-stripping set, you will keep cold air from getting into your home. This, in turn, makes it easier for your heating costs to stay down. A great stripping set ensures that your heat will stay indoors without escaping.

But to make it work well enough for you, it is important to watch for how the weatherstripping is organized. You must use a powerful set to see that you’re keeping the air inside your home under control.

What Is Weatherstripping Made With?

Weatherstripping materials are typically made with thick caulk materials. These include items that can block out cold temperatures in an area. This would work well within your home if you are cautious with making it functional.

Rubber compounds may also be added. It is sturdy and thick and can also reflect cold temperatures quite well.

Anything that is used can be rigid or soft. A softer option may be used around the inside part of your home. This could help you to secure any spots inside a room while being soft enough to handle the force that comes from a door closing. A harder application is best if you have space where you need an extra bit of protection, particularly when getting it added outside your home.

DIY Weather-stripping

Where Is It Added At?

Weatherstripping materials can be added around the windows and doors outside your home. This is to add a slight barrier that keeps air from moving through and being a nuisance.

It can also work on doors inside your home. This could help you out if you want to keep the air in your space from escaping or otherwise being too hard to handle at a given time.

As this is applied in the right spots, it should be easy for a space to feel comfortable. You should get the materials added around the surfaces around doors and windows to allow air within a room to stay intact and safe.

When Should It Be Replaced?

This part of your sealant should be replaced every couple of years. The wear on such items can keep a spot from feeling relaxed. You must watch out so you know it’s not hard to get it replaced.

You must use a strong adhesive on your sealant materials. Most weatherstripping applications come with their own bonding materials although you might have to provide one of your own items to see that it won’t be too hard to use.

Watch as you get a great weatherstripping application in your home to keep heating costs down. You will see when you use weather-stripping that it will not be a real struggle to use. You might be amazed at how well it can work for the demands you hold.

Finding the Right Plumbing Contractors in Dallas, TX

If you are looking around to find plumbing contractors in Dallas, you should look closely. There are many different types of contractors that are worth your time. You just must watch for what you are getting into when finding someone who can help you out. This is to see that you aren’t hiring the wrong Dallas Plumbing Company

Check on Services

dallas plumber

Hire the right Dallas Plumbing Company.

Plumbing contractors in Dallas can help you out with a vast variety of different services. You can hire different contractors that are experienced in fields like removing clogs, installing sinks or repairing pipes among other points. Check carefully to see that any plumber you wish to hire understands the ins and outs of the task you need help with.

 

Insurance Is a Must

You must ensure that your contractor is properly insured. This means that you will not be at risk of losing money for any damages that occur during the plumbing repair or maintenance process. The plumber should have insurance to bear the risk and cost that comes with taking care of many things in the plumbing process.

Check on How the Plans Work

You should talk with any plumber of interest to you about how a plan will work. This includes a look at the individual steps that will be used, the materials required for the job and so forth. A clearly thought out plan must be organized and prepared by your contractor.

Any plans that entail a sensible series of steps and ideas for the task at hand are always welcome. This shows that there is a sense of control over your project and that there will be nothing wrong coming out of the contractor’s services when used right.

An estimate may also help you out. You can get information on how much money it will cost for you to use a service provided to you. A qualified contractor will especially offer a sensible plan for charging you without being too complicated or otherwise hard to handle.

Look at Clean Water

The process of cleaning may be critical to the success of a plumbing project. Your plumbing contractor must work in a secure and sanitary fashion. This is to see that your project will be easy to handle without being too rough in some way. When used right, you will get enough clean water without having any issues in hand.

Plumbing contractors in Dallas will help you out quite a bit if you hire the right people. Make sure you ask proper contractors for help so you will get the most out of your repair or maintenance needs without any hassles or other problems in some sense.

What is HVAC Replacement?

 HVAC Replacement

In the simplest words, HVAC replacement means parting ways with your old HVAC units and getting a new one in its stead. HVAC replacement does not necessarily have to be a complete replacement. HVAC system has two separate units – air conditioning and boiler and furnaces unit. Air conditioning keeps you cool in summers and boilers keep you warm in winters.

Do I Need Repair or Replacement?

commercial hvac servicesSometimes, major or minor components of the system may need to be replaced. But if you are just replacing certain components, it is basically a repair. The true replacement is when the entire HVAC unit is renewed (considering cooling and heating units as separate).

So, how do you know it is the time for the replacement? HVAC is a pretty sturdy and robust system. Therefore, identifying the right time for the replacement could get a little difficult.

 Expected Life of an HVAC Unit

Some people do not know that the manufacturer of the HVAC system also specifies its expected service life. According to them, when that time has passed, the HVAC unit must be replaced. But sometimes your system seems to be fully functional and you see no reason to meddle with it.

This is where you will need to think a little differently. The expected service life is about ten years for the HVAC system. It means that it has already served you enough. While it may seem that it is doing a good job, in reality it might be costing you much more than you expected in terms of energy consumption.

Sometimes your HVAC system will give you clear or subtle indications that the time for the replacement has come.

 What if I Have a Furnace?

If you are using a furnace that is gas-fired then its most important component is heat exchanger. The heat exchanger is designed to let the transfer of heat from the gas burner take place. This heat is then circulated through the entire HVAC system. If there is even small damage to the exchanger, you will want to get it replaced immediately.

Heat exchangers sustain damages in the form of holes and cracks. Over time, after prolonged use, the heat exchangers become more prone to damages. They have the endurance capacity and if they get heated beyond that they will get damaged. This is something that is quite common when the HVAC is old. However, if the filter is not cleaned properly, it will get damaged much earlier.

Rusting is a Problem 

Rusting is another big culprit causing the damage to the heat exchangers. The rusting is caused when the humidity and moisture level in the area are high. Sometimes, when the furnace of the heating unit is too close to the AC it also causes the rusting of the exchanger.

As far as air conditioning unit is concerned, if you hear too much noise from the duct or the cooling is not effective, it could be the time to go for replacement.