Gas Water Heater Vs. Electric Water Heater

You have an old gas water heater and it is time to replace it with a new one but, you don’t know whether to replace for another gas or an electric one, do you? What to do before you make such a decision?

Why compare one vs. another?

water heater boxIn today’s world, people are frequently talking about saving energy, especially at home. And when referring to home energy savings, people will remember the basics such as turning the lights off when not in use and buying appliances that promote the highest energy efficiency level.

Although these two steps are good, it usually is as far as we all go in attempting to save energy. One of the most important energy saving equipment found inside every home is the water heater. The boiler is overlooked by most homeowners almost 90% of the time.

In fact, not only gas water heater but electric ones are responsible for about 25% of home energy consumption, so, why not think about saving energy with the water heater?

This article will concentrate about the pros and cons of a gas water heater Vs an electric one, what you should know about each one of them before making your decision.

Gas Water Heater:

Most gas water heaters that are available in today’s market runs out of natural gas, however, if you live in the country, it is most likely that your water heater is an electric or a propane gas one.

gas water heaterGas water heater is considered one of the most energy-efficient available in the market today, especially, if compared with an electric one.

Gas heaters are more efficient to heat the water due to the burner power in the bottom of the tank.

Most gas water heaters run at 80% to 90% efficiency, which means, no matter what is done with the installation and ventilation, the electric heater will lose about 10% to 20% of energy. Gas heaters are much better for a large family, due to their quick recovery rate.

The average fuel cost for gas water heater per therm is $0.50 or $136 per year, if it is $0.60 per therm, that the yearly cost would be $163, if the price per therm $0.70, the yearly cost then would be $190.

Electric Water Heater:

electric water heaterElectric water heaters run at 220v which means that if the home is not upgraded with the proper electric wire and power box, this means that the homeowner will have to make an investment to upgrade the home electricity, which might cost several hundreds of dollars or, even over a thousand.

Electric water heaters need electric wires rated to run the water heater. It also needs to be properly venting the carbon monoxide from inside the home to the outside. Electric heaters run usually at 100% efficiency, but, the tank doesn’t keep hot water for too long and, the recovery rate is usually slower than the gas heaters. Especially, there’re more than 4 people in the house.

If a family of 5 or more people, the electric water heater is not a good option. The average cost of electricity of an electric water heater is $0.08 per kilowatt-hour, so the yearly cost would be $390, if the price per kilowatt-hour is $0.10 then, the yearly cost will be $488 but, if the price per kilowatt- hour is $0.12, the yearly cost will be $585.

Natural Gas Price

Per Therm Yearly Cost

$0.50—–$136.00

$0.60—–$163.00

$0.70—–$190.00

Propane Price

Per Gallon Yearly Cost

$0.95—–$283.00

$1.05—–$313.00

$1.15—–$343.00

Electricity Price

Kilowatt-hour Yearly Cost

$0.08———$390.00

$0.10———$488.00

$0.12———$585.00

Concluding:

When comparing a gas to an electric water heater, it is evident that a natural gas water heater will be the best option to have in the home; however, such a choice will only make sense, if the home already has the proper electrical or gas connections ready for it.

So, the best way to go is to first check the home to see what kind of installation that is already there, there, consult the Dallas water heater professionals, a certified electrician and a certified plumber in gas to provide you with a bid for either of the necessary upgrade, then, see what makes sense to you.

Also, visualize your saving not only in the present time but, at as well as, on the long run and, with the one that will save you money the most and will provide the most benefit.

Disclaims: Remember, this is an informational page only, you are responsible for your decisions, and this site is in no way responsible for your decision.

 

Touchless Sinks, Faucets, and More

Have you ever been in a restaurant or other public place where you noticed that there were no proper knobs on a sink? Today more people are turning to touchless fixtures for their plumbing projects. It is intriguing to see how such fixtures can be used in your home and how easy it can be to install them.

How a Touchless Fixture Works

Basically, what happens is that a motion sensor will be applied to your sink area. This will read any significant movements.

As the sensor identifies motions like your hands going over the area, it will trigger the sink or toilet. It will prompt the plumbing to let out enough water.

This works without the need for added knobs. It also helps with saving water which will save you money.

How Is It Installed?

Such a feature can be installed into your home using a small sensor. When this is added, the fixture will work with an electric connection. It will use this to monitor what moves in an area and to trigger the water as it identifies things.

Does it Use Too Much Energy?

A separate connection is typically needed for the sensor. Fortunately, that connection will work alongside other fixtures in your bathroom. It should not drain lots of energy. If anything, it will not use any energy at all until it identifies when something is in the area to get the water out.

 

Make sure you look at this feature if it’s time for a bathroom remodel.  You will be surprised at how well it can be used in your home. Want help installing a touchless toilet or sink? Call Dallas Plumbing Company Today!

Battle Global Warming Starting at Home

The Battle Versus Global Warming: Start in your house

Carbon dioxide and other greenhouse gases are a huge cause of global warming or at least the increase in the earth’s temperature level.  A programmable timer will allow your houses temperature level to be low when you are not there. However, you can set it to turn your heat on right prior to you showing up!

While it is essential to keep in mind that our houses are not the only reason for co2 emissions, we need to all begin someplace. What much better location then inside our houses?

Hot Water Heater Blanket

HVAC Repair ServicesYou can assist to stop the influences of global warming and assist the environment. One way to do this is by putting a hot water heater blanket on your heater. When correctly made use of, hot water heater blankets can allow you to reduce the temperature level. This can conserve you time, as well as decrease the emissions from your house.

Even if you do not formally think or support global warming, you might still be interested in the modifications that you are seeing. Fortunately there are many ways in which we can all assist. If you have an interest in doing your part to assist, stop, or decrease the effect of global warming, you will initially wish to begin in your very own house.

As more political figures, researchers, and stars voice their issues about global warming, more Americans are starting to take notice. If everyone does something small, it could be huge.

Saving Home Heating

In keeping with your heat, it might be a good idea to have your home inspected. Numerous people have no concept how much heat gets away from their house.

What Can you do? Update the insallation in your house and update or fix your windows. Those repair works might be able to pay for themselves overtime,

Global warming is a problem that is commonly discussed, it is a problem that still triggers issue. In the summer season and fall of 2007, southern states, such as Georgia and Tennessee experienced life altering dry spell conditions. This resulted in the stringent enforcement of water bans and water constraints.

Minimize Power Usage

Did you understand that by minimizing your electrical power usage, you can not just assist to conserve the environment and fight worldwide warming, you can conserve yourself a substantial quantity of cash each year?

Ways that you can lower electrical energy in your house consist of:

  • changing all or many of the light bulbs in your house to energy efficient ones.
  • Install energy efficient home appliances
  • Turn lights off when not in use

Home Air Conditioner Parts and Services That a Professional Can Handle

Your home’s air conditioner is a critical part of your property. You must keep it working at all times to ensure that it won’t struggle with hassles relating to certain pieces around your unit not working as well as needed. Today you can get various home AC parts and accessories for all parts of your air conditioner so you will stay fully chilled and cooled off. However, some parts are easier for professional services to install.

 Duct Jackets Are Often Added

Home Air Conditioner Parts and ServicesMany HVAC specialists in Dallas can work with different duct jackets to protect the ducts around the AC unit. Duct jackets are designed to insulate the ducts in your home, thus keeping them from bearing with heat or air losses. You must get a professional to take care of such problems in your home so they will not be any worse to handle than needed.

Check On Circuit Boards

Circuit boards are often found on many AC units. These are designed to make it easier for power to be distributed evenly to the entire AC unit. This in turn will create a better setup that is not too complicated or hard to operate. However, a specialist will have to get a circuit board reviewed within any HVAC setup so it will keep power running right without risking any further losses over time.

 Filtration Items Are a Must

The filters within an air conditioner must be analyzed carefully to ensure that they will stay functional and ready for use. An air conditioner can be treated with only the finest filters that are not only able to fit into a spot but can also be replaced as required. You must be certain that you get your filters cleaned out or replaced on occasion. An HVAC specialist can securely take care of your filters and clear them, fix them or even get new models as quickly as possible.

Don’t Forget the Fans

The fans in an air conditioner unit can wear to the point where they might become dirty or potentially loose and misaligned from the rest of the AC unit. This can be a real problem but it does not have to be too harsh if you are able to get a proper fan installed or at least adjusted in some manner. An AC expert can help you to fix up the problem and get it all repaired with care so your space will be treated right.

What About the Condensing Unit?

A good condensing unit can be serviced or even replaced as needed. It can be restored to clear out old debris and components that might get in the way of how it works. This in turn will provide you with a clearer and easier to handle component that is not too hard to work with.

Remember that your home AC unit can be critical to your success. Be sure to watch for how the AC parts and services you are getting will work for your general requirements so you will get the coverage and support that you deserve.

 

Prevent Frozen Pipes | Dallas Plumbing Company | February 24, 2015

Aside

If you live anywhere near DFW you are certainly experiencing the effects of the recent freezing weather! WFAA’s weather forecast system is predicting the following areas will receive more snow, sleet and rain tonight with the low temperatures dipping below freezing, again!

February 24, 2015 Weather Report

Freezing Weather Report by WFAA for the DFW Dallas Fort Worth area on Wednesday, February 25, 2015. Snow, Sleet and Freezing Temperatures.

While the kiddos may be excited about another “Snow Day”, the adults of the house worry about things like freezing pipes! Here are a few tips to keep your plumbing in working order.

PREVENT FROZEN PIPES

1. Disconnect all outdoor hoses.

2. Add covers to all outdoor spigots.

3. Allow all faucets to drip throughout the night. Open both the hot and cold stems.

4. Open cabinet doors to expose plumbing, especially in rooms facing the exterior walls of the home.

5. Wrap pipes near exterior walls with blankets or towels for extra insulation.

6. Keep the heat in your home above 65 degrees, even if you plan on leaving.

7. Check for drafts and seal off open areas. Even a temporary fix (example: towel under the door) can be a big help!

Tip and Tricks to help prevent frozen pipes brought to you by Dallas Plumbing Company and Kitchens and Baths Designer Showroom! Emergency Plumbing Tips to help you save time and money.

Tip and Tricks to help prevent frozen pipes brought to you by Dallas Plumbing Company and Kitchens and Baths Designer Showroom! Emergency Plumbing Tips to help you save time and money.

These tips should help prevent any freezing! If you do experience frozen or burst pipes, call your local experts, Dallas Plumbing Company for emergency service! 214.340.6300

 

Buy The Best HVAC Parts in Dallas, Texas

Anyone who uses HVAC machines knows that unless they are well taken care of, they cannot function well. Indeed, there are many problems that people go through just because they do not know how to maintain their machines. One of the most important things is to buy good HVAC parts. If you live near Dallas-Fort Worth, TX, we can help you find the parts you need.

HVAC PartsA look at those that can be found in the stores shows that there are many types that a client can choose from.

What you need to know is that even though there are good ones, others may not even come close to what you need. Here are some of the factors to consider when making the choices.

 What Kind of HVAC System Do You Have?

 You need to understand that there are many types of machines that can be used for this purpose. You only need to see those that are available through both on and offline stores to understand that indeed, the list is almost endless. You therefore should start by knowing what is best for your specific kind of machine before you go ahead to purchase it. Do not just buy something because your friends have bought it. In fact, you will be baffled to find out that what is good for you is not even close to what others need.

 Go For Quality Plumbing and Heating Parts

 When looking for HVAC parts, you need to go for superior quality. This is because quality is the source of every other good thing that you can ever hope for. For instance, if you want the items to last long, you have no option but to go for top quality. You definitely do not want to keep going back to the stores every now and then just because you want to purchase these items. The good thing however is that regardless of where you come from, there always is many good quality parts to choose from at Dallas Plumbing Company in Dallas, TX.

Purchasing New HVAC Parts

 When buying these parts, you need to be sure of the quality that they are likely to add to your machines. There definitely is a problem that you want to solve by purchasing new HVAC parts and so, you need to ensure that they are the specific ones that can help you to get the best results. You should look at the overall performance that you will get from the machines after the parts have been replaced. If you notice that there is almost no value, it will be an indication that you should try something else.

 After you have found the right HVAC parts, the next task is to find a contractor who can fit them. You need someone who has a deep understanding of how these machines work and how best to repair them. Do not just hire anyone that you find in your neighborhood because you never know what to expect from them. In fact, you might just end up making the whole situation worse when you thought that you were doing a good thing. Before hiring a HVAC technician, it is important to look at what they are capable of.

Quality and Affordable Plumbing and Heating Parts For Repair

Quality and affordable plumbing and heating parts for repair can give the homeowner peace of mind knowing that repairing heating, cooling and plumbing systems poses no problem for technical knowledgeable experts. They have a thorough knowledge of these systems and how they operate, knowing full well that installing the wrong part can have disastrous effects and always at inopportune times.

Plumbing Service

We Offer Many Plumbing Services in Dallas

HVAC Parts

Call About Plumbing and HVAC Parts

A reputable team of experts always have the right parts in stock to ensure prompt and reliable repairs. They create well organised inventory systems for their plumbing and heating business in order to easily track the specific part. Their parts come from top brands such as Bosch, Fantech, Panasonic, Grundfos, Mitsubishi, Daikin, Unico and many others.
Get your Systems Back Up-and-Running Quickly

Taking time to get a system up-and-running again could actually cost you more money in the long run as the system deteriorates further. Their aim of a reputable plumbing team is to provide the highest quality parts at the most affordable prices. If an exact replacement isn’t available, they make use of the best alternative.

They search from their inventory of parts for toilet- and faucet repair parts, water heaters, commercial faucets and valves, well pumps and water coolers to find the right plumbing and heating parts. If you are a DIY expert, if you go into a plumbing and heating parts shop, it is a good idea to take in the broken part with you as it helps the shop assistants make sure you get the right replacement part.

When looking for plumbing and heating parts for repair, you want the inventory to be able to meet any need, whether remodeling- or building a new home. Plumbing and heating parts for repair from fully licensed, full-service companies will ensure that your plumbing, heating and cooling systems are always running at peak performance all year round. A comprehensive inventory of parts simply means that whatever your problem, it can be solved in the quickest and most professional way.
A Quick and Effective Distribution Network

There is no need to deal with a host of different plumbing suppliers when you can get all your repair parts under one-roof. When you look for repair parts online, you get an inventory of parts complete with specs and price. These parts are needed for electrical, cooling and heating requirements in homes and businesses. Contractors, handymen, homeowners, businesses and DIY enthusiasts all make use of these parts.

Whether people need to repair or replace an entire furnace for instance, whether you go into a shop or you buy online, there are always experienced, knowledgeable staff who can assist you with making the selection of the proper equipment to do the job correctly. Once you have selected your products, there is an effective distribution network which assures customers have quick delivery of a broad range of quality products. They aim to make sure customers have exactly what they need every time and also in time.

The Right Repair Parts meet Regulatory Standards

Choose the right parts for plumbing and heating systems as they can have a radical effect on quality. The best parts for repair create safe home- and work environments and also reduce the risk associated with meeting regulatory standards.